27 real Energy Management & Audit questions from the Plant & Utility Ops bank, as asked in Indian campus drives and tech interviews. Every question has a verified answer and an AI-tutor explanation on placd — free to start.
1. What is Mandatory energy audit?
Junior
A.Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit
B.Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
C.moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
D.ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
2. Which term means: "Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit"?
A.Mandatory energy audit — energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
B.Mandatory energy audit — DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
C.Mandatory energy audit — for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
D.Mandatory energy audit — Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit
A.DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
B.ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
C.energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
D.total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated
A.Energy performance indicator — for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
B.Energy performance indicator — moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
C.Energy performance indicator — DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
D.Energy performance indicator — ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
A.Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit
B.total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated
C.ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
D.DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
8. Which term means: "DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission"?
A.Power factor incentive and penalty — moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
B.Power factor incentive and penalty — energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
C.Power factor incentive and penalty — for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
D.Power factor incentive and penalty — DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
A.ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
B.moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
C.energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
D.maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents
11. Which term means: "maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents"?
A.Contract demand penalty — energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
B.Contract demand penalty — moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
C.Contract demand penalty — DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
D.Contract demand penalty — maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents
A.ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
B.moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
C.total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated
D.for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
14. Which term means: "moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years"?
A.IE3 motor replacement economics — for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
B.IE3 motor replacement economics — Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit
C.IE3 motor replacement economics — moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
D.IE3 motor replacement economics — Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
A.for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
B.maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents
C.energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
D.Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
17. Which term means: "for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power"?
A.Affinity laws — ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
B.Affinity laws — total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated
C.Affinity laws — for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
D.Affinity laws — maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents
A.DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
B.moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
C.for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
D.energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
20. Which term means: "energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison"?
A.Specific energy consumption — for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
B.Specific energy consumption — energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
C.Specific energy consumption — Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
D.Specific energy consumption — moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
A.Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit
B.energy used per unit of output, such as kWh per tonne of cement or kWh per cubic metre of water pumped, the benchmark for plant-to-plant comparison
C.Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
D.moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
23. Which term means: "Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges"?
A.PAT scheme — moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
B.PAT scheme — DISCOM tariffs typically reward average PF above 0.95 and penalise below 0.90 on the demand or energy bill, with rates fixed by each state commission
C.PAT scheme — Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
D.PAT scheme — ISO 50001 metric such as kWh per tonne, tracked against an energy baseline to prove improvement of the significant energy uses
A.total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated
B.for centrifugal pumps and fans flow varies with speed, head with speed squared and power with speed cubed, so a 20% speed cut on a VFD saves about half the power
C.maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents
D.moving from IE1 to IE3 gains about 2–4 percentage points of efficiency; at more than 4000 running hours a year the payback is usually under three years
26. Which term means: "total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated"?
A.Optimum transformer loading — total loss is least where load loss equals no-load loss, typically at 40–60% loading, so lightly loaded units are switched off and their loads consolidated
B.Optimum transformer loading — Perform Achieve and Trade under NMEEE sets SEC reduction targets for designated consumers over three-year cycles; over-achievers earn ESCerts of one tonne of oil equivalent traded on power exchanges
C.Optimum transformer loading — Energy Conservation Act 2001 requires designated consumers to be audited by a BEE-accredited energy auditor, moving from a preliminary walk-through to a detailed instrumented audit
D.Optimum transformer loading — maximum demand is recorded over a 15 or 30 minute integration period; exceeding the sanctioned figure attracts 1.5–2 times the demand charge on the excess, which a demand controller prevents
Answers, AI explanations, and a free readiness check
Sign up free to check your answers with explanations, ask the AI tutor anything on any question, and take the free 2-minute readiness check for a scored result. The full AI mock interview, scored like a real panel, unlocks with Pro.